Tour Resources

Baggage limits, paperwork, money and life on the road — everything to sort before and during a tour

Voltages, frequencies, plugs and transformers — what your gear needs in each country

General guidance only, not electrical advice. Mains supplies, venue wiring and local rules vary — always read the label on your own gear, check the official source linked on each card, and use a qualified electrician for anything involving rewiring, voltage conversion inside an amp, or doubt about stage power.

Voltage, frequency & plugs by region

Two things change when you cross a border: the voltage coming out of the wall and the shape of the hole it comes out of. Check both per country, not per continent.

Type I plug face: two angled flat pins with a vertical earth pin below
TYPE I

Lime marks earth

Australia & New Zealand

230V, 50Hz, Type I plug — the flat angled pins.

  • Nominal supply is 230V at 50Hz, though a lot of older local gear is still labelled 240V; the two are the same supply.
  • Type I sockets take the Australian/NZ plug. Argentina and China also use a Type I plug, but do not assume an Australian lead is legal or safe in those countries.
  • Australian and New Zealand sockets are often switched at the wall — check the switch before you chase a dead amp.
  • Standard domestic and venue outlets are 10A. A 15A lead (wider earth pin) will not fit a 10A socket, which catches out imported distro and larger PA amps.

Will your gear run on it?

Read the label on the back of every piece before you pack it. The answer is printed there, and it decides whether you need a $20 adapter or a 20kg transformer.

Read the input label

Three numbers tell you everything: voltage, frequency, and amps or watts.

  • "INPUT: 100–240V ~ 50/60Hz" means the device handles any mains in the world. It needs a plug adapter only.
  • "INPUT: 230V ~ 50Hz" or "120V ~ 60Hz" alone means the device is single-voltage and needs a transformer outside that range.
  • A range like 220–240V covers all of Europe, the UK, Australia and most of Asia, but not the Americas or Japan.
  • Photograph every label before you pack. It is much easier than reading the back of a rack at 4pm in a dark venue.

Usually fine anywhere

Switch-mode supplies are almost always universal.

  • Laptop chargers, phone chargers, audio interfaces and most USB power bricks are 100–240V.
  • Modern pedalboard supplies are built for this: Strymon markets Zuma as compatible with 100V, 120V and 240V and anywhere in between.
  • Most in-ear and wireless systems ship with a universal supply, but the wall wart is often country-specific — check whether you need a different lead or just a plug adapter.
  • Digital modellers, powered speakers and class-D bass heads are usually universal. Usually is not always: check the label on each one.

Valve amps are the problem child

Most are built for one voltage at the factory.

  • A US 120V valve amp plugged into 230V will destroy its mains transformer, often instantly and with smoke.
  • Some amps have a voltage selector on the back or inside the chassis. If yours does, set it before you plug in, and make it part of the load-in checklist.
  • Changing an amp's voltage properly means a tech swapping or re-tapping the mains transformer — not something to do the week you fly.
  • For a single overseas run, hiring local backline is almost always cheaper and safer than shipping a valve amp and a transformer.

What frequency actually affects

50Hz versus 60Hz matters less than voltage, but it is not nothing.

  • Transformers rated for 60Hz should not be run on 50Hz: the core saturates, losses climb and the transformer overheats. The reverse — a 50Hz transformer on 60Hz — is fine.
  • So US 120V/60Hz gear run through a step-down in Europe is on the risky side of that rule; European 50Hz gear taken to the US is not.
  • Anything with a synchronous motor (old tape machines, some Leslie cabinets, mains-clock devices) runs at the wrong speed on the wrong frequency, whatever the voltage.
  • Switch-mode supplies rated 50/60Hz genuinely do not care, which is why universal gear is the easy answer.

Transformers, converters & adapters

Three different products, constantly confused in shops and on stage. Only one of them is safe for an amp.

Know which one you need

Adapter changes the shape. Transformer changes the voltage.

  • A plug adapter only changes the pin shape. It does nothing to voltage — plugging 230V gear into 120V through one just means it does not work.
  • A step-down or step-up transformer actually changes the voltage and is what amps and other single-voltage gear need.
  • Small travel 'converters' sold for hairdryers are usually not continuous-duty and are not suitable for amps or anything with a motor or valve.
  • Neither changes frequency. Nothing in a normal touring rig converts 50Hz to 60Hz.

Sizing a transformer

Add up the gear, then leave headroom.

  • Total the VA or watt rating on every device you will plug in; the total must stay under the transformer's rating. TAD sells a 1000VA unit and describes it as enough for all common guitar amps and even an Ampeg SVT.
  • Leave at least 30–50% headroom over the total, because amps draw far more on transients than their idle draw suggests.
  • Transformers are heavy — a 1000VA toroidal unit is a real piece of luggage. Weigh it and count it against your baggage allowance.
  • One transformer per amp is the simplest setup on stage; sharing one across a backline means one failure kills everything.

Leads and adapters that actually work

Bring leads, not a bag of loose adapters.

  • Most amps, mixers and powered speakers use a standard IEC C13 ('kettle') socket. The cheapest fix is a local IEC lead bought in each country rather than adapters stacked on your own.
  • Carry a couple of short earthed extension leads with your home sockets on them, then one local lead into each: one adapter per band, not one per pedal.
  • Check the adapter is earthed (three pins, not two). Unearthed travel adapters are for phone chargers, not backline.
  • A cheap multimeter or socket tester weighs nothing and settles arguments about whether the stage power is actually wired correctly.

Stage power & safety

Wet stages, shared circuits and old wiring. The rules that keep people alive and the rig quiet.

Never lift the mains earth

The classic hum fix that can kill someone.

  • Removing or defeating the earth pin — a 'cheater plug' or a snapped-off pin — makes the equipment unsafe to use. Sennheiser's guidance puts it plainly: never isolate ground at the mains connection.
  • Fix hum at the signal end instead: a DI box with a ground lift, or an audio isolation transformer on the offending connection.
  • Run the whole backline and PA from the same circuit or distro where you can; ground loops usually come from gear split across circuits.
  • A singer holding an earthed microphone while playing an unearthed guitar amp is the exact scenario that has killed performers.

Before you plug into a strange stage

Two minutes of checking beats a dead show.

  • Ask what the stage circuits are rated at and how many there are; work out whether the PA, backline and lighting share one.
  • Plug a socket tester in first in older venues and anywhere outdoors — reversed live and neutral is common in old wiring.
  • Outdoors, on grass or anywhere wet, insist on an RCD (earth-leakage protection). Many festivals provide it; bring your own inline RCD if the routing has doubt in it.
  • Generators sag when a big amp kicks in and can spike when a load drops. Keep audio off the same generator as lighting and catering if you can.

Paperwork and certification

Some territories want to see that your gear is tested.

  • UK venues and many European festivals ask for PAT certificates for band-owned mains gear; annual testing is the usual recommendation, or every six months for gear on the road constantly.
  • Keep the certificate as a PDF in your file vault, not just stickers on the back of amps.
  • Hired backline is the hire company's responsibility to certify — get their paperwork with the hire confirmation.
  • Gear insurance often assumes safe use; defeating an earth or overloading a transformer is the kind of thing that voids a claim.

Power checklists

Work through these per tour. Anything that needs assigning can become a task on the Tasks board.

Before you book

  • List the voltage, frequency and plug type for every country on the routing
  • Photograph the input label on every piece of mains gear
  • Decide per leg: universal gear, hire local backline, or carry a transformer
  • Ask each promoter what stage power and how many circuits the room has

Packing

  • Earthed plug adapters for every country, plus two spares
  • One or two earthed extension leads with home sockets on them
  • Spare IEC leads and, for the UK, spare 3A, 5A and 13A fuses
  • Socket tester or multimeter, and an inline RCD for outdoor shows

At load-in

  • Set any amp voltage selector before plugging in — check it, every show
  • Test the stage sockets before the rig goes live
  • Put the backline and PA on the same circuit where possible
  • Check the transformer is rated above the total load, and keep it ventilated

If something hums

  • Never pull the earth pin or fit a cheater plug
  • Lift the ground at one end of the signal path with a DI box
  • Move gear onto one circuit before blaming the cables
  • Kill dimmer packs and LED wall boxes near the stage and test again

Your band's notes

Transformer you own and its rating, adapters already bought, venues with known power quirks.

No notes yet.